Shop
Dash A
The extremely bright dashboard indicators! Almost invincible when turned off, but unbeatable in action: Thanks to the mounting position under the handlebars, the new Dash indicators virtually disappear visually at the front of the motorcycle. At the same time, the Kellermann Dash indicators offer maximum brightness with minimum size. This means that the credo of Kellermann's compact indicators now also applies to the new generation of dashboard indicators: "sensationally small - spectacularly bright". The optimized light control of the new Dash family is also achieved by a sophisticated system of lenses and reflectors. The Kellermann HighPower LED** and EXtranz® - Extreme Optical Transparency technology are used here.The complete electronics of the Dash A Dark are in the casing, this indicator can be plugged into the 12 volt net directly.* * Possibly electronic equipment is needed to regulate the flashing rate.** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction.ECE-testedfor front sensationally small, spectacularly bright EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications European design protection
Atto® WL Dark
The ´White´ Light The Atto® WL Dark is the new kid on the block of the highly successful Atto® family and at once the first single position light from Kellermann. The Atto®/Atto® Dark already defined a completely new category of indicators: sensationally small and spectacularly bright. Compact and illuminating power: With this combination the Atto® WL Dark is a real sensation! The light surface of the Atto® WL Dark would fit four times on a 1 Cent coin! This consequent reduction offers completely new styling options for the motorcycle. In fact, the Atto®WL Dark basically disappears on the motorcycle.The position light shines with the intensity that has made the products of Kellermann legendary and the company over and over again a trendsetter in this segment. The Atto® WL Dark offers maximum illuminating power at minimal size, in short: sensationally small, spectacularly bright! Therefore the Atto® WL Dark is enhancing safety on the road.The Atto® WL Dark can be used on multiple applications including quads, cars and trailers (homologated according to ECE-R 6/ R 7).The optimized light channeling is managed through a smart system of lenses and reflectors. This combination is possible thanks to the use of the well known Kellermann HighPower LED technology**, along with the new EXtranz® - Extreme Optical Transparency technology.The complete electronics of the Atto® WL Dark are in the casing, this position light can be plugged into the 12 volt net directly.* * Possibly electronic equipment is needed to regulate the flashing rate. ** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction. ECE-tested for front and rear sensationally small, spectacularly bright EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5x0,5x6,5 fastening screw Measure: Length 14mm, max. diameter 10mm, glass diameter 7,8mm European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
Atto® RB Dark vm
’Seeing red’ right to the point! The Atto® RB Dark is another kid on the block of the highly successful Atto® family and probably the world’s smallest street legalrear and brake light for motorcycles. The Atto® already defined a completely new category of indicators: sensationally smalland spectacularly bright. The new rear and brake light Atto® RB Dark will be no different, but due to its dual function will take things even further. The light surface of the Atto® RB Dark would fit four times on a 1 Cent coin! Therefore the tail of a bike can get a complete clean look and feel. This rear and brake light will only grab your attention when it really has to! The brake light of the Atto® RB Dark warns with an intensity that is second to none. It keeps the following traffic at distance.Therefore the Atto® RB Dark is enhancing safety on the road. The Atto® RB Dark can be installed in different ways and offers more options to individualize a bike. It can be mounted in pairs or centrally as a single light! The optimized light channeling is managed through a smart system of lenses and reflectors. This combination is possible thanks to the use of the well known Kellermann HighPower LED technology**, along with the new EXtranz® - Extreme Optical Transparency technology. The complete electronics of the Atto® RB Dark are in the casing, this rear and brake light can be plugged into the 12 volt net directly.* * Possibly electronic equipment is needed to regulate the flashing rate. ** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction. ECE-tested for front and rear horizontal mounting sensationally small, spectacularly bright EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5x0,5x6,5 fastening screw Measure: Length 14mm, max. diameter 10mm, glass diameter 7,8mm European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
Harley-Davidson FLSS 1802 SOFTAIL SLIM S ab MJ 2016 Atto® DF Set
BMW S 1000 RR Atto® DF Set(for original 3-in-1 rear lights)Complete set with all necessary parts for mounting and electrical connection of Atto® DF rear on a BMW BMW S 1000 RR .Contents:2x156.200 Atto® DF / piece 99.95€1x152.751 Mounting plate C-Evo / set 19.95€1x111.100 i.NEX - V12 / piece 89.95€1x111.522 i.NEX - Connector set 122 / set 12.95€
Silent rubber adapter KH 1000
Silent rubber adapter KH 1000 Spare part for KH 1000 Length: 10 mm, with M8 thread
BMW R 1300 GS Adventure Jetstream® CL + Jetstream® DF Set
BMW R 1300 GS Adventure Jetstream® CL + Jetstream® DF SetComplete set with all necessary parts for mounting and electrical connection of Jetstream® CL at the front and Jetstream® DF at the rear on a BMW R 1300 GS Adventure.Contents:2x194.200 Jetstream® CL / piece 129.95€2x196.200 Jetstream® DF / piece 129.95€1x123.762 Mounting plate B3 / set 29.95€1x123.763 Mounting plate B4 / set 29.95€1x111.100 i.NEX - V12 / piece 89.95€1x111.520 i.NEX - Connector set 120 / set 14.95€1x111.522 i.NEX - Connector set 122 / set 12.95€
Multi-function piece for BL 1000
Multi-function piece for BL 1000 yellow / BL 1000 white (halogen) without mounting rubber + nut
Mounting Plates for Suzuki
Mounting Plates 123.750 used for:Universal Adapterplate for all Suzuki Motorcycles front/rear
Content: 2 Piece(s) (€6.48 / 1 Piece(s))
Yamaha XSR 700 2022 4 x Atto® Set
Honda VFR 800X Crossrunner MJ 2018 4 X Atto® SetComplete set with all necessary parts for mounting and electrical connection of Atto® at the front and rear of a Honda VFR 800X Crossrunner MJ 2018.Contents:4x152.200 Atto® / piece 64.95€2x152.751 Mounting plate C-Evo / set 19.95€1x111.100 i.NEX - V12 / piece 89.95€2x111.544 i.NEX - Connector set 144 / set 14.95€
Posi-Lock Cable Connector
Posi-Lock cable connector splash water connections. The cable is connection between seconds, without soldering.
Content: 5 Piece(s) (€1.99 / 1 Piece(s))
i.NEX - Connector set 110
i.NEX - Connector set 110 Vehicle-specific plug & play set for connecting the i.NEX consisting of two adapter cables with matching plug, 2 extension cables and cable connectors. The set is suitable for the following motocycle models: Aprilia Tuono V4 1100 Factory MJ 2017 -2019 (front indicators)
i.BOS - EL 33
i.BOS - EL 33 The i.BOS systems provide a quick fix, if after the installation of DF versions control lights in the cockpit function inaccurately. When changing the original indicators to LED or Halogen the indicating frequency is automatically altered. This is adjusted for parallel switched power resistors. The right selection of the suitable power resistors is listed in the table below. If you are not sure which resistor you need, please don’t hesitate to contact us via the contact form (Technical Dept) on our homepage. Required is 1 set for 2 indicators / 2 DF indicators (indicator, rear light, brake light) One i.BOS - EL 33 parallel to the rear light and one i.LOAD - IL 7,5 parallel to the brake light are needed.
i.NEX - Connector set 162
i.NEX - Connector set 162Vehicle-specific plug & play set for connecting the i.NEX consisting of two adapter cables with matching plug, 2 extension cables and cable connectors. The set is suitable for the following motocycle models: Indian Scout Bobber MJ 2015 (rear 3in1)
i.NEX - Connector set 110
i.NEX - Connector set 110 Vehicle-specific plug & play set for connecting the i.NEX consisting of two adapter cables with matching plug, 2 extension cables and cable connectors. The set is suitable for the following motocycle models: Aprilia Tuono V4 1100 Factory MJ 2017 -2019 (front indicators)
Rhombus DF
Simply triple Our innovative indicator-brake-rear light combination in our distinctive micro Rhombus housing offers new styling options for the rear of your bike. The original tail light can be eliminated. Made to the highest standards of quality, the micro Rhombus DF are now available with the option of clear or dark tinted lenses. With its characteristically bright double rear lights the micro Rhombus DF are the latest trend in indicator design. Kellermann HighPower LED Technology** coupled with its compact housing translates to an extremely lightweight unit. Suitable for all motorcycle models*. * Electrical accessories may be required to match indicators signal frequency. ** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction. ECE-tested for rear Replaces the existing brake/rear light as well as the indicator Sensational new rear look Kellermann HighPower LED Technology Long Life Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M8x20 thread Replaceable flexible rubber adapter which protects the indicator from vibration damage and vandalism
Rhombus Extreme
A talented edge Our innovative indicator-brake-rear light combination maximizes your individual styling option at the rear of your bike! Optically fully disguised due to its reduction in size and an all-rounder at the same time: The original tail light can be eliminated and replaced by beaming double rear lights based on high-performance LEDs and the Kellermann HighPower LED Technology.** Inconspicuous at rest, unbeatable in action: The brake light of the Rhombus S DF Dark warns with an intensity that is second to none. It keeps the following traffic at distance, thus enhancing safety on the road. As the complete electronics are in the casing the Rhombus S DF Dark allows for a significant reduction in weight. Suitable for all motorcycle models.* * Electronical accessories may be required to match indicators signal frequency. ** Combination out of the IC operated Longlife Protection Guard system with high-performance-LED latest type of construction. ECE-tested for rear Replaces the existing brake/rear light as well as the indicator Sensational new rear look Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5 x 0,5 x 6,5 mm thread European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
Rhombus DF
Simply triple Our innovative indicator-brake-rear light combination in our distinctive micro Rhombus housing offers new styling options for the rear of your bike. The original tail light can be eliminated. Made to the highest standards of quality, the micro Rhombus DF are now available with the option of clear or dark tinted lenses. With its characteristically bright double rear lights the micro Rhombus DF are the latest trend in indicator design. Kellermann HighPower LED Technology** coupled with its compact housing translates to an extremely lightweight unit. Suitable for all motorcycle models*. * Electrical accessories may be required to match indicators signal frequency. ** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction. ECE-tested for rear Replaces the existing brake/rear light as well as the indicator Sensational new rear look Kellermann HighPower LED Technology Long Life Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M8x20 thread Replaceable flexible rubber adapter which protects the indicator from vibration damage and vandalism
BMW S 1000 R 4 x Atto® Set Kopie
BMW S 1000 R Atto® SetComplete set with all necessary parts for mounting and electrical connection of Atto® at the front and rear of a BMW BMW S 1000 R.Contents:4x152.200 Atto® / piece 64.95€2x152.751 Mounting plate C-Evo / set 19.95€1x111.100 i.NEX - V12 / piece 89.95€2x111.520 i.NEX - Connector set 120 / set 14.95€
Vehicle adapter Suzuki/ Yamaha/ Triumph
Fahrzeugadapter Honda Artikel verfügbar solange der Vorrat reicht.
BMW R 1250 GS Adventure Atto® + Atto® DF Set
BMW R 1250 GS Adventure Atto® + Atto® DF SetComplete set with all necessary parts for mounting and electrical connection of Atto® front and Atto® DF rear on a BMW R 1250 GS Adventure.Contents:2x152.200 Atto® / piece 64.95€2x156.200 Atto® DF / piece 99.95€2x152.751 Mounting plate C-Evo / set 19.95€1x111.100 i.NEX - V12 / piece 89.95€1x111.520 i.NEX - Connector set 120 / set 14.95€1x111.522 i.NEX - Connector set 122 / set 12.95€
BMW R 1250 GS Adventure Atto® DF Set
BMW R 1250 GS Adventure Atto® DF SetComplete set with all necessary parts for mounting and electrical connection of Atto® DF rear on a BMW R 1250 GS Adventure.Contents:2x156.200 Atto® DF / piece 99.95€1x152.751 Mounting plate C-Evo / set 19.95€1x111.100 i.NEX - V12 / piece 89.95€1x111.522 i.NEX - Connector set 122 / set 12.95€
Honda VFR 800X Crossrunner MJ 2018 4 X Atto® Set
Honda VFR 800X Crossrunner MJ 2018 4 X Atto® SetComplete set with all necessary parts for mounting and electrical connection of Atto® at the front and rear of a Honda VFR 800X Crossrunner MJ 2018.Contents:4x152.200 Atto® / piece 64.95€2x152.751 Mounting plate C-Evo / set 19.95€1x111.100 i.NEX - V12 / piece 89.95€2x111.544 i.NEX - Connector set 144 / set 14.95€
Yamaha TRACER 7 GT 2023 4 x Atto® Set
Honda VFR 800X Crossrunner MJ 2018 4 X Atto® SetComplete set with all necessary parts for mounting and electrical connection of Atto® at the front and rear of a Honda VFR 800X Crossrunner MJ 2018.Contents:4x152.200 Atto® / piece 64.95€2x152.751 Mounting plate C-Evo / set 19.95€1x111.100 i.NEX - V12 / piece 89.95€2x111.544 i.NEX - Connector set 144 / set 14.95€
Rhombus PL
Alpha indicator The micro Rhombus indicator has a striking design that is also available with bright position lights. Thanks to modern high-performance-LEDs and our specially control technology**, the micro Rhombus PL ensures better visibility in road traffic. In addition, they also allow others in traffic to better estimate your speed. Connected about the instrument lighting***, the increased power and crystal clear double look creates the impression of daylight-bright lights. Suitable for all motorcycle models*. * A load-independant relay or power resistors may be required to match indicators signal frequency. ** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction.*** The existing side light must be deactivated. ECE-tested for front Increased safety because of improved visibility Replaces the existing position light as well as the indicator Sensational new front look Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 6 and 12 volt DC applications With M8x20 thread Replaceable flexible rubber adapter which protects the indicator from vibration damage and vandalism