rear
Jetstream® CL With the Jetstream® CL, Kellermann now offers the world's most spectacular motorcycle indicator with a cruising light. The Jetstream® CL is therefore the first indicator with this function on the accessory market. With the cruising light function, the indicators light up permanently as a position light with amber color. When the indicator is activated, it then takes over the indicator function with the sequential light effect. Two parallelly illuminated position lights visually widen the silhouette of the vehicle, which is particularly helpful for the visibility of the bike for oncoming traffic. The brightness of the Kellermann Jetstream® CL is extreme; no other sequential lighting indicator with ECE approval for motorcycles has achieved these levels of this intensity to date. The indicator function is displayed via a bright and slit-like beam along the entire wing edge. Kellermann thus pushes the upper limit of brightness and ensures maximum added safety on the road.With the new Jetstream® CL, all motorcycles can now be retrofitted with an amber cruising light and indicator function with sequential lighting effect. Motorcycles with a standard cruising light and indicator function can be changed to the Kellermann Jetstream® CL. Highest illuminating power Kellermann high power LED technology State-of-art „IC“- chip technology 32 MHz real time micro processor controlled Silent-Current, advanced Power Saving Algorithm High measure of visibility across a wide angle range Longlife Protection Guard®, IC operated, 330 kHz Flow-optimized metal housing, high quality manufacturingSuitable for 12 volt DC applications With M8 x 20 mm thread High-quality vibration-absorbing bearing European design protection
Sensation With the Atto®/Atto® Dark we made the almost impossible possible: This indicator is extremely small and spectacularly bright at the same time. Compact and illuminating power: With this combination the Atto®/Atto® Dark is a real sensation! This is our most compact indicator ever. For comparison: The light surface of the Atto®/Atto® Dark would fit four times on a 1 Cent coin! This consequent reduction offers completely new styling options for the motorcycle. In fact, the Atto®/Atto® Dark basically disappears on the motorcycle. This indicator will only grab your attention when it really has to!The Atto®/Atto® Dark flashes with the intensity that has made the products of Kellermann legendary and the company over and over again a trendsetter in this segment. This indicator offers maximum illuminating power at minimal size, in short: sensationally small, spectacularly bright! We advise not to look for too long into the beam of this little power house.The optimized light channeling is managed through a smart system of lenses and reflectors. This combination is possible thanks to the use of the well known Kellermann HighPower LED technology**, along with the new EXtranz® - Extreme Optical Transparency technology.The complete electronics of the Atto®/Atto® Dark are in the casing, this indicator can be plugged into the 12 volt net directly.* * Possibly electronic equipment is needed to regulate the flashing rate.** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction.ECE-tested for front and rear sensationally small, spectacularly bright EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5x0,5x6,5 fastening screw Measure: Length 14mm, max. diameter 10mm, glass diameter 7,8mm European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
Classic meets Hightech The Bullet 1000® was created with a clear goal: An indicator with the classic bullet look and a classy Kellermann design, but equipped with modern LED technology. A newly developed light technology (Kellermann-HPT®) creates a homogenous ring of light. Design quality is not only a question of shape and surfaces but also a result of the complete look and feel when the lights are on. The high quality metal housing with a maximum diameter of 39 mm is like a jewel on the motorcycle. It is available in chrome, black and matte chrome. The Bullet 1000® works with any sophisticated bike design. The Bullet 1000® comes in four different technical versions: Extreme indicator, indicator with yellow position light, indicators with white position light and indicator with rear and brake light. Bullet 1000 DF The Bullet 1000® DF is a rear indicator in combination with a rear and brake light function. It replaces the existing indicators, brake and rear light. The light of the continuously glowing red rings give the tail of the motorcycle a spectacular look**. When breaking, the light circle of the brake light shines strong and clear, the clear message to the following traffic is: Keep your distance. The Bullet 1000® DF at the tail and the Bullet 1000® PL, Bullet 1000® PL white or Bullet 1000® Extreme in the front are the perfect combination for your motorcycle.* * Electrical accessories may be required to match indicators signal frequency. ** Combination out of the IC operated Longlife Protection Guard system with high-performance-LEDs latest type of construction. ECE-tested for rear Replaces the existing brake/rear light as well as the indicator Special flashing effect Unique and homogeneous light ring Extreme light power HPT®- Homogenous Projection Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M8 x 20 fastening screw European design protection
Sensation With the Atto® we made the almost impossible possible: This indicator is extremely small and spectacularly bright at the same time. Compact and illuminating power: With this combination the Atto® is a real sensation! This is our most compact indicator ever. For comparison: The light surface of the Atto® would fit four times on a 1 Cent coin! This consequent reduction offers completely new styling options for the motorcycle. In fact, the Atto® basically disappears on the motorcycle. This indicator will only grab your attention when it really has to! The Atto® flashes with the intensity that has made the products of Kellermann legendary and the company over and over again a trendsetter in this segment. This indicator offers maximum illuminating power at minimal size, in short: sensationally small, spectacularly bright! We advise not to look for too long into the beam of this little power house. The optimized light channeling is managed through a smart system of lenses and reflectors. This combination is possible thanks to the use of the well known Kellermann HighPower LED technology**, along with the new EXtranz® - Extreme Optical Transparency technology. The complete electronics of the Atto®/Atto® Dark are in the casing, this indicator can be plugged into the 12 volt net directly.* * Possibly electronic equipment is needed to regulate the flashing rate. ** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction. ECE-tested for front and rear sensationally small, spectacularly bright EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5x0,5x6,5 fastening screw Measure: Length 14mm, max. diameter 10mm, glass diameter 7,8mm European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
A sensational all-rounder A 3in1 sensation as it hasn’t been seen before: The Atto® DF is the latest and by far most spectacular member of Kellermann’s successful Atto® series! The probably world’s smallest street legal indicator is now available in triple function with an integrated rear and brake light. Behind the extremely small yet sensationally bright Atto® DF lays a multifunctional all-rounder: At the rear it is visually almost completely disguised with a light surface, which would fit four times on a 1 Cent coin! In result the rear of the motorcycle can be designed as clean and individual as never before. However, in action the Atto® DF shines with an intensity which has made Kellermann products legendary – it’s not the size but the illumination power that counts. Indicators, rear and brake light warn with an uncompromising intensity, clearly signalling the following traffic to keep its distance. Kellermann’s well-known HighPower LED technology** and EXtranz® - Extreme Optical Transparency Technology manage an optimized light channelling through a smart system of lenses and reflectors and thus enabling this combination of sensational brilliance and minimal size. The Atto® DF can be combined with various other series e.g. Atto® or Bullet 1000®. As the complete electronics are in the casing the Atto® DF allows for a significant reduction in weight. * Possibly electronic equipment is needed to regulate the flashing rate. ** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction. ECE-tested for rear replaces the existing rear / brake light as well as indicators sensational new rear look EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5x0,5x6,5 fastening screw European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
A talented edge Our innovative indicator-brake-rear light combination maximizes your individual styling option at the rear of your bike! Optically fully disguised due to its reduction in size and an all-rounder at the same time: The original tail light can be eliminated and replaced by beaming double rear lights based on high-performance LEDs and the Kellermann HighPower LED Technology.** Inconspicuous at rest, unbeatable in action: The brake light of the Rhombus S DF Dark warns with an intensity that is second to none. It keeps the following traffic at distance, thus enhancing safety on the road. As the complete electronics are in the casing the Rhombus S DF Dark allows for a significant reduction in weight. Suitable for all motorcycle models.* * Electronical accessories may be required to match indicators signal frequency. ** Combination out of the IC operated Longlife Protection Guard system with high-performance-LED latest type of construction. ECE-tested for rear Replaces the existing brake/rear light as well as the indicator Sensational new rear look Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5 x 0,5 x 6,5 mm thread European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
A talented edge Our innovative indicator-brake-rear light combination maximizes your individual styling option at the rear of your bike! Optically fully disguised due to its reduction in size and an all-rounder at the same time: The original tail light can be eliminated and replaced by beaming double rear lights based on high-performance LEDs and the Kellermann HighPower LED Technology.** Inconspicuous at rest, unbeatable in action: The brake light of the Rhombus S DF Dark warns with an intensity that is second to none. It keeps the following traffic at distance, thus enhancing safety on the road. As the complete electronics are in the casing the Rhombus S DF Dark allows for a significant reduction in weight. Suitable for all motorcycle models.* * Electronical accessories may be required to match indicators signal frequency. ** Combination out of the IC operated Longlife Protection Guard system with high-performance-LED latest type of construction. ECE-tested for rear Replaces the existing brake/rear light as well as the indicator Sensational new rear look Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5 x 0,5 x 6,5 mm thread European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
Classic meets Hightech The Bullet 1000 was created with a clear goal: An indicator with the classic bullet look and a classy Kellermann design, but equipped with modern LED technology. A newly developed light technology (Kellermann-HPT) creates a homogenous ring of light. Design quality is not only a question of shape and surfaces but also a result of the complete look and feel when the lights are on. The high quality metal housing with a maximum diameter of 39 mm is like a jewel on the motorcycle. It is available in chrome, black and matte chrome. The Bullet 1000 works with any sophisticated bike design. The Bullet 1000 comes in four different technical versions: Extreme indicator, indicator with yellow position light, indicator with white position light, and indicator with rear and brake light. Bullet 1000 Extreme The Bullet 1000 Extreme is a pure indicator with high luminosity and has the ECE-R6 approval for all vehicles. The big advantage of the indicator is that you can install it closer to the main light than normal indicators, giving you more options to customize your bike. The continuous light ring shows the LED typical fast response** combined with Bullet typical soft response of the inner light section. Altogether a harmonic indicator performance that blends in with the great overall look and feel of this amazing product.* * Electrical accessories may be required to match indicators signal frequency. ** Combination out of the IC operated Longlife Protection Guard system with high-performance-LEDs latest type of construction. ECE-tested for front and rear Applicable on all vehicles (e. g. motorcycles, quads, cars, Super Seven, trailers, etc.) Special flashing effect Unique and homogeneous light ring Extreme light power HPT&- Homogenous Projection Technology Kellermann HighPower LED Technology Longlife Protection Guard, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M8 x 20 fastening screw European design protection
A sensational all-rounder A 3in1 sensation as it hasn’t been seen before: The Atto® DF is the latest and by far most spectacular member of Kellermann’s successful Atto® series! The probably world’s smallest street legal indicator is now available in triple function with an integrated rear and brake light. Behind the extremely small yet sensationally bright Atto® DF lays a multifunctional all-rounder: At the rear it is visually almost completely disguised with a light surface, which would fit four times on a 1 Cent coin! In result the rear of the motorcycle can be designed as clean and individual as never before. However, in action the Atto® DF shines with an intensity which has made Kellermann products legendary – it’s not the size but the illumination power that counts. Indicators, rear and brake light warn with an uncompromising intensity, clearly signalling the following traffic to keep its distance. Kellermann’s well-known HighPower LED technology** and EXtranz® - Extreme Optical Transparency Technology manage an optimized light channelling through a smart system of lenses and reflectors and thus enabling this combination of sensational brilliance and minimal size. The Atto® DF can be combined with various other series e.g. Atto® or Bullet 1000®. As the complete electronics are in the casing the Atto® DF allows for a significant reduction in weight. * Possibly electronic equipment is needed to regulate the flashing rate. ** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction. ECE-tested for rear replaces the existing rear / brake light as well as indicators sensational new rear look EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5x0,5x6,5 fastening screw European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
An edge in disguise The Rhombus series is extended and now presents itself in a particular compact version! The drastic reduction in size allows for completely new design standards on the motorcycle: when not in use its miniature format and the characteristic tinted glass take undercover to the next level. In action however the high performance LEDs provide a spectacularly bright light, which Kellermann indicators are now for! The well-known Kellermann HighPower LED Technology** and the new EXtranz- Extreme Optical Transparency Technology enable an optimized light channeling. As the complete electronics of the Rhombus S Dark are in the casing, this indicator can be plugged into the 12 volt net directly.*Combined at front and back the offer a perfect look. Suitable for all motorcycle models.* * Electronical accessories may be required to match indicators signal frequency. ** Combination out of the IC operated Longlife Protection Guard system with high-performance-LED latest type of construction. ECE-tested for front and rear Strongly tinted glass – spectacularly bright Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5 x 0,5 x 6,5 mm thread European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
An edge in disguise The Rhombus series is extended and now presents itself in a particular compact version! The drastic reduction in size allows for completely new design standards on the motorcycle: when not in use its miniature format and the characteristic tinted glass take undercover to the next level. In action however the high performance LEDs provide a spectacularly bright light, which Kellermann indicators are now for! The well-known Kellermann HighPower LED Technology** and the new EXtranz- Extreme Optical Transparency Technology enable an optimized light channeling. As the complete electronics of the Rhombus S Dark are in the casing, this indicator can be plugged into the 12 volt net directly.*Combined at front and back the offer a perfect look. Suitable for all motorcycle models.* * Electronical accessories may be required to match indicators signal frequency. ** Combination out of the IC operated Longlife Protection Guard system with high-performance-LED latest type of construction. ECE-tested for front and rear Strongly tinted glass – spectacularly bright Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5 x 0,5 x 6,5 mm thread European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
’Seeing red’ right to the point! The Atto® RB Dark is another kid on the block of the highly successful Atto® family and probably the world’s smallest street legalrear and brake light for motorcycles. The Atto® already defined a completely new category of indicators: sensationally smalland spectacularly bright. The new rear and brake light Atto® RB Dark will be no different, but due to its dual function will take things even further. The light surface of the Atto® RB Dark would fit four times on a 1 Cent coin! Therefore the tail of a bike can get a complete clean look and feel. This rear and brake light will only grab your attention when it really has to! The brake light of the Atto® RB Dark warns with an intensity that is second to none. It keeps the following traffic at distance.Therefore the Atto® RB Dark is enhancing safety on the road. The Atto® RB Dark can be installed in different ways and offers more options to individualize a bike. It can be mounted in pairs or centrally as a single light! The optimized light channeling is managed through a smart system of lenses and reflectors. This combination is possible thanks to the use of the well known Kellermann HighPower LED technology**, along with the new EXtranz® - Extreme Optical Transparency technology. The complete electronics of the Atto® RB Dark are in the casing, this rear and brake light can be plugged into the 12 volt net directly.* * Possibly electronic equipment is needed to regulate the flashing rate. ** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction. ECE-tested for front and rear horizontal mounting sensationally small, spectacularly bright EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5x0,5x6,5 fastening screw Measure: Length 14mm, max. diameter 10mm, glass diameter 7,8mm European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
"Lights on, Spot® on!" - Special edition with a sporty shape As Kellermann is known for, the Spot® is also super compact and brilliantly bright like no other indicator. This special edition is unusual due to its much sportier shape. With the Spot®, Kellermann's big anniversary party continues: over 30 years of the finest lighting technology on motorbikes - Made in Germany, of course!The shape of the Spot® makes all the difference: Slightly extended in length and a strong base that fits closely to the motorbike. This looks sporty, not only on sports bikes! The Spot® also looks really good on any bike. "Lights on, Spot® on" - the new Spot® makes for a particularly strong appearance!Kellermann Spot® - compact and bright as ever, but sportier!ECE-tested for rear EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5x0,5x6,5 fastening screw Measure: Length 14mm, max. diameter 10mm, glass diameter 7,8mm European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
Sensation With the Atto® we made the almost impossible possible: This indicator is extremely small and spectacularly bright at the same time. Compact and illuminating power: With this combination the Atto® is a real sensation! This is our most compact indicator ever. For comparison: The light surface of the Atto® would fit four times on a 1 Cent coin! This consequent reduction offers completely new styling options for the motorcycle. In fact, the Atto® basically disappears on the motorcycle. This indicator will only grab your attention when it really has to! The Atto® flashes with the intensity that has made the products of Kellermann legendary and the company over and over again a trendsetter in this segment. This indicator offers maximum illuminating power at minimal size, in short: sensationally small, spectacularly bright! We advise not to look for too long into the beam of this little power house. The optimized light channeling is managed through a smart system of lenses and reflectors. This combination is possible thanks to the use of the well known Kellermann HighPower LED technology**, along with the new EXtranz® - Extreme Optical Transparency technology. The complete electronics of the Atto® are in the casing, this indicator can be plugged into the 12 volt net directly.* * Possibly electronic equipment is needed to regulate the flashing rate. ** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction. ECE-tested for front and rear sensationally small, spectacularly bright EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5x0,5x6,5 fastening screw Measure: Length 14mm, max. diameter 10mm, glass diameter 7,8mm European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto
"Lights on, Spot® on!" - Special edition with a sporty shape As Kellermann is known for, the Spot® is also super compact and brilliantly bright like no other indicator. This special edition is unusual due to its much sportier shape. With the Spot®, Kellermann's big anniversary party continues: over 30 years of the finest lighting technology on motorbikes - Made in Germany, of course!The shape of the Spot® makes all the difference: Slightly extended in length and a strong base that fits closely to the motorbike. This looks sporty, not only on sports bikes! The Spot® also looks really good on any bike. "Lights on, Spot® on" - the new Spot® makes for a particularly strong appearance!Kellermann Spot® - compact and bright as ever, but sportier!ECE-tested for front and rear EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5x0,5x6,5 fastening screw Measure: Length 14mm, max. diameter 10mm, glass diameter 7,8mm European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
A brilliant edge The Rhombus S Extreme is one of the brightest Kellermann indicators available so far. In combination with a drastic reduction in size new design standards are set – not only for motorcycles! The Rhombus S Extreme is allowed for use on multiple applications including quads, cars and trailers (homologated according to ECE-R6). On motorcycles this indicator can be installed within twenty millimetres of the main headlamp, thus blending seamlessly into the visual appearance of the bike. Three LEDs and the Kellermann HighPower LED Technology** generate an impressive and previously unattained bright signal. Due to this greater illumination power it is recognized more quickly in traffic providing for maximum road safety.* * Electronical accessories may be required to match indicators signal frequency.** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction. ECE-tested for front and rear Applicable on all vehicles(e. g. motorcycles, quads, cars, Super Seven, trailers, etc.) Extreme light power and brilliant optic Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5 x 0,5 x 6,5 mm thread European design protection Please note the extensive electronic equimenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
A brilliant edge The Rhombus S Extreme is one of the brightest Kellermann indicators available so far. In combination with a drastic reduction in size new design standards are set – not only for motorcycles! The Rhombus S Extreme is allowed for use on multiple applications including quads, cars and trailers (homologated according to ECE-R6). On motorcycles this indicator can be installed within twenty millimetres of the main headlamp, thus blending seamlessly into the visual appearance of the bike. Three LEDs and the Kellermann HighPower LED Technology** generate an impressive and previously unattained bright signal. Due to this greater illumination power it is recognized more quickly in traffic providing for maximum road safety.* * Electronical accessories may be required to match indicators signal frequency.** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction. ECE-tested for front and rear Applicable on all vehicles(e. g. motorcycles, quads, cars, Super Seven, trailers, etc.) Extreme light power and brilliant optic Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5 x 0,5 x 6,5 mm thread European design protection Please note the extensive electronic equimenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
"Lights on, Spot® on!" - Special edition with a sporty shape As Kellermann is known for, the Spot® is also super compact and brilliantly bright like no other indicator. This special edition is unusual due to its much sportier shape. With the Spot®, Kellermann's big anniversary party continues: over 30 years of the finest lighting technology on motorbikes - Made in Germany, of course!The shape of the Spot® makes all the difference: Slightly extended in length and a strong base that fits closely to the motorbike. This looks sporty, not only on sports bikes! The Spot® also looks really good on any bike. "Lights on, Spot® on" - the new Spot® makes for a particularly strong appearance!Kellermann Spot® - compact and bright as ever, but sportier!ECE-tested for rear EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5x0,5x6,5 fastening screw Measure: Length 14mm, max. diameter 10mm, glass diameter 7,8mm European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
"Lights on, Spot® on!" - Special edition with a sporty shape As Kellermann is known for, the Spot® is also super compact and brilliantly bright like no other indicator. This special edition is unusual due to its much sportier shape. With the Spot®, Kellermann's big anniversary party continues: over 30 years of the finest lighting technology on motorbikes - Made in Germany, of course!The shape of the Spot® makes all the difference: Slightly extended in length and a strong base that fits closely to the motorbike. This looks sporty, not only on sports bikes! The Spot® also looks really good on any bike. "Lights on, Spot® on" - the new Spot® makes for a particularly strong appearance!Kellermann Spot® - compact and bright as ever, but sportier!ECE-tested for rear EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5x0,5x6,5 fastening screw Measure: Length 14mm, max. diameter 10mm, glass diameter 7,8mm European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
The pillion This classic rear indicator combines tested Halogen technology with stylish, timeless design. Its compact build and high quality metal housing mean reduced weight. It is the ideal companion to our BL 1000 series handlebar end indicators. Suitable for all motorcycle models*. * Electronical accessories may be required to match indicators signal frequency. ECE-tested for rear 6 Watt Halogen lamp High quality metal housing Suitable for 12 volt DC applications With M8x20 thread Replaceable flexible rubber adapter which protects the indicator from vibration damage and vandalism
"Lights on, Spot® on!" - Special edition with a sporty shape As Kellermann is known for, the Spot® is also super compact and brilliantly bright like no other indicator. This special edition is unusual due to its much sportier shape. With the Spot®, Kellermann's big anniversary party continues: over 30 years of the finest lighting technology on motorbikes - Made in Germany, of course!The shape of the Spot® makes all the difference: Slightly extended in length and a strong base that fits closely to the motorbike. This looks sporty, not only on sports bikes! The Spot® also looks really good on any bike. "Lights on, Spot® on" - the new Spot® makes for a particularly strong appearance!Kellermann Spot® - compact and bright as ever, but sportier!ECE-tested for front and rear EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5x0,5x6,5 fastening screw Measure: Length 14mm, max. diameter 10mm, glass diameter 7,8mm European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
Simply Triple Our innovative indicator-brake-rear light combination in the stylish micro 1000® housing makes it possible to take a new direction when individualizing the rear of your bike. The original tail light can be eliminated. The micro 1000® DF Dark are made to the highest standards of quality and are now available with the option of clear or dark tinted lenses. The characteristically bright double rear lights of the micro 1000® DF Dark sets new standards. Using our tried and tested Kellermann HighPower LED Technology** coupled with its compact housing translates to an extremely lightweight unit. Suitable for all motorcycle models*. * Electronical accessories may be required to match indicators signal frequency. ** Combination out of the IC operated Longlife Protection Guard system with high-performance-LED latest type of construction. ECE-tested for rear Replaces the existing brake/rear light as well as the indicator Sensational new rear look Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M8x20 thread Replaceable flexible rubber adapter which protects the indicator from vibration damage and vandalism
Clean Look The Atto® DF Integral is the first built-in version from Kellermann, it can be fully integrated into the fairing or other components. The slim casing almost fully disappears and gives the desired ‘clean look’ when it comes to customizing. Behind the extremely small yet sensationally bright Atto® DF Integral lays a multifunctional all-rounder: At the rear it is visually almost completely disguised with a light surface, which would fit four times on a 1 Cent coin! In result the rear of the motorcycle can be designed as clean and individual as never before. However, in action the Atto® DF Integral shines with an intensity which has made Kellermann products legendary – it’s not the size but the illumination power that counts. Indicators, rear and brake light warn with an uncompromising intensity, clearly signalling the following traffic to keep its distance.Kellermann’s well-known HighPower LED technology** and EXtranz® - Extreme Optical Transparency Technology manage an optimized light channelling through a smart system of lenses and reflectors and thus enabling this combination of sensational brilliance and minimal size. The Atto® DF Integral can be combined with various other series e.g. Atto® or Bullet 1000®.The complete electronics of the Atto® DF Integral are in the casing, this Atto® DF Integral can be plugged into the 12 volt net directly.* In order to protect the Atto© DF Integral from a possible thermal overload, a heat sink in the form of an optionally screw-on ribbed housing is provided. Dimensions heat sink approx.: 24.5x8.9 mm * Possibly electronic equipment is needed to regulate the flashing rate. ** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction. ECE-tested for rear Completely new styling options Replaces the existing rear / brake light as well as indicators Sensational new rear look EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications European design protection With M5 x 0,5 x 6,5 mm fastening screw
’Seeing red’ right to the point! The Atto® RB Dark is another kid on the block of the highly successful Atto® family and probably the world’s smallest street legalrear and brake light for motorcycles. The Atto® already defined a completely new category of indicators: sensationally smalland spectacularly bright. The new rear and brake light Atto® RB Dark will be no different, but due to its dual function will take things even further. The light surface of the Atto® RB Dark would fit four times on a 1 Cent coin! Therefore the tail of a bike can get a complete clean look and feel. This rear and brake light will only grab your attention when it really has to! The brake light of the Atto® RB Dark warns with an intensity that is second to none. It keeps the following traffic at distance.Therefore the Atto® RB Dark is enhancing safety on the road. The Atto® RB Dark can be installed in different ways and offers more options to individualize a bike. It can be mounted in pairs or centrally as a single light! The optimized light channeling is managed through a smart system of lenses and reflectors. This combination is possible thanks to the use of the well known Kellermann HighPower LED technology**, along with the new EXtranz® - Extreme Optical Transparency technology. The complete electronics of the Atto® RB Dark are in the casing, this rear and brake light can be plugged into the 12 volt net directly.* * Possibly electronic equipment is needed to regulate the flashing rate. ** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction. ECE-tested for front and rear horizontal mounting sensationally small, spectacularly bright EXtranz® - Extreme Optical Transparency Technology Kellermann HighPower LED Technology Longlife Protection Guard®, IC operated, 330 kHz High quality metal housing Suitable for 12 volt DC applications With M5x0,5x6,5 fastening screw Measure: Length 14mm, max. diameter 10mm, glass diameter 7,8mm European design protection Please note the extensive electronic equipmenthttps://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/