Atto® WL Dark
€69.95
Available, delivery time: 1-3 days
Product information "Atto® WL Dark"
The ´White´ Light
The Atto® WL Dark is the new kid on the block of the highly successful Atto® family and at once the first single position light from Kellermann. The Atto®/Atto® Dark already defined a completely new category of indicators: sensationally small and spectacularly bright. Compact and illuminating power: With this combination the Atto® WL Dark is a real sensation!
The light surface of the Atto® WL Dark would fit four times on a 1 Cent coin! This consequent reduction offers completely new styling options for the motorcycle. In fact, the Atto®WL Dark basically disappears on the motorcycle.
The position light shines with the intensity that has made the products of Kellermann legendary and the company over and over again a trendsetter in this segment. The Atto® WL Dark offers maximum illuminating power at minimal size, in short: sensationally small, spectacularly bright! Therefore the Atto® WL Dark is enhancing safety on the road.
The Atto® WL Dark can be used on multiple applications including quads, cars and trailers (homologated according to ECE-R 6/ R 7).
The optimized light channeling is managed through a smart system of lenses and reflectors. This combination is possible thanks to the use of the well known Kellermann HighPower LED technology**, along with the new EXtranz® - Extreme Optical Transparency technology.
The complete electronics of the Atto® WL Dark are in the casing, this position light can be plugged into the 12 volt net directly.*
* Possibly electronic equipment is needed to regulate the flashing rate.
** Combination out of the IC operated Longlife Protection Guard® system with high-performance-LEDs latest type of construction.
ECE-tested for front and rear
- sensationally small, spectacularly bright
- EXtranz® - Extreme Optical Transparency Technology
- Kellermann HighPower LED Technology
- Longlife Protection Guard®, IC operated, 330 kHz
- High quality metal housing
- Suitable for 12 volt DC applications
- With M5x0,5x6,5 fastening screw
- Measure: Length 14mm, max. diameter 10mm, glass diameter 7,8mm
- European design protection
Please note the extensive electronic equipment
https://www.kellermann-online.com/en/products/accessories-for-indicators/accessories-atto/
| DC on-board power supply: | 12 V |
|---|---|
| ECE-type approval: | all vehicles |
| Functional features: | Position light |
| Length (without thread/fastening): | 14 mm |
| Lens colour: | strongly tinted |
| Mounting: | mounted indicator |
| Mounting: | universell |
| Mounting thread: | M5 x 0,5 x 6,5 mm |
| Position: | front |
| Produktlisting-Features: | Position light |
| Technology: | LED |
| Ø max.: | 10 mm |
Montagezubehör
Bulb holder evo for micro 1000® Halogen (from 2004)
Atto® mounting plate C - Evo, black 33 mm, fitting on most models of different brands, e.g. Aprilia, BMW, Ducati, Moto Guzzi, Honda, Triumph
Content: 2 Piece(s) (€9.97 / 1 Piece(s))
Atto® rigid mounting M10 x 20mm, black for use with original 10mm bore
Atto® rigid mounting M8 x 20mm, black for use with original 8mm bore
Atto® rigid mounting M8 x 40mm, black for use with original 8mm bore
Variable mounting adaptor M6, black This adaptor offers a clean and easy solution for various mounting options and thus replaces an otherwise complex custom-made construction.It consists of two parts: A clamping sheet and a shank nut with an M6 internal thread. The clamping sheet, which can be shifted and rotated on the shank nut, is compatible with any M5 threaded lamp (Atto®, micro S, Rhombus S) at every angle.Due to the variances of this mounting the lamp can be installed in perfect alignment with the direction of traffic and is locked in place with grub screws. For example underneath the instruments (see pictures attached).Simply replace the shaft nut of the brake or clutch lever by this shank nut. As on the pictures attached, the clamping sheet can also be installed together with the handlebar mirror.
Elektronisches Zubehör
Micro relay for the pros The R 1 flasher relay has very small dimensions and flashes independently of load at a steady 75 pulses per minute. It also has a connection available for the flasher dashboard light. It is easily installed into the feed to the indicator switch, or can be swapped with the original 2-3 pole flasher relay. It is therefore suitable for all motorcycles with indicator switches. Should the change to LED indicators result in the non-intentionally activated indicators also flashing; then the indicator control light must also be connected to the R 1 relay. The ‘hazard warning’ effect will then be effectively All necessary components required for installation are included. ECE-tested Simple installation in feed to the indicator switch or swap the original 2-3 pole flasher relay Connection to indicator control light also possible Restricts the accompanying flashing of non-activated indicators Load-independent / steady flash rate Switching capacity 0-50W by 12V/ 0-24W by 6V Very small dimensions 22 x12 x 6 mm (L/W/H) Suitable for indicator switches Suitable for 6 and 12 volt DC applications
i.BOS - CL1 Serves as a quick fix for inaccurate cockpit displays The i.BOS systems (intelligent boxing operation system) provide a quick fix, if after the installation of the indicator the control light flashes too quick or other control lights in the cockpit function inaccurately. i.BOS - CL1 provides correct function of the control and hazard light, e.g. when using DF versions for Harley Davidson models with HD-LAN. *Additionally and on case by case the option "LED indicator" has to be activated in the software. Required is 1 set for 2 indicators / 2 DF indicators (indicator, rear light, break light)
i.BOS - EL1 Serves as a quick fix for inaccurate cockpit displays The i.BOS systems (intelligent boxing operation system) provide a quick fix, if after the installation of the indicator the control light flashes too quick or other control lights in the cockpit function inaccurately. i.BOS - EL1 provides correct function of the hazard light, e.g. when using DF versions. *Additionally and on case by case the option "LED indicator" has to be activated in the software. Required is 1 set for 2 indicators / 2 DF indicators (indicator, rear light, light)
i.LOAD - IL 10 Usage of micro 1000® Halogen indicators instead of original 21 watt indicators - 1 piece per indicator When installing new indicators the flashing rate of the indicator or the control light may increase. Load independent relays (e.g. R2) or multifunctional assistance systems (e.g. CR4®) can fix the problem. If the installation is not possible or favored ,an i.LOAD can also fix the problem.
i.SED V12 suitable for vehicles with 12 volt indicator application For example when mounting indicators with higher wattage than original indicators on vehicles where the ground is „plus“ but not „minus“ as usual „DF“ products on vehicles where the indicators ground is switched but not the plus as usual
i.SED V6 suitable for vehicles with 5-9 volt indicator application For example when mounting indicators with higher wattage than original indicators with higher voltage than original indicators on vehicles where the ground is „plus“ but not „minus“ as usual
Posi-Lock cable connector splash water connections. The cable is connection between seconds, without soldering.
Content: 9 Piece(s) (€1.44 / 1 Piece(s))
Posi-Lock cable connector MINI Splash water connections The cable is connection between seconds, without soldering
Content: 5 Piece(s) (€1.99 / 1 Piece(s))